Knowing the actual weight of your truck and trailer is essential before heading out on a towing trip. Manufacturer specifications provide useful starting points, but they cannot tell you exactly how much your particular combination weighs after adding passengers, fuel, camping equipment, tools, water, and hitch hardware.
A pickup advertised with a high towing capacity can still exceed its payload, rear axle, or gross vehicle weight rating (GVWR) when connected to a heavily loaded trailer. The only reliable way to understand your actual loading situation is to measure it.
For many pickup and RV owners in the United States, a CAT Scale at a participating truck stop offers a convenient way to do this. Its multiple weighing platforms allow you to measure the front axle, rear axle, and trailer axle group separately. With an additional truck-only weighing, you can also calculate the trailer’s loaded weight and estimate how much weight is being transferred to the towing vehicle.
This guide explains how to prepare, position your combination, obtain the correct tickets, perform the calculations, and interpret the results.
What Is a CAT Scale?
A CAT Scale is a commercial vehicle weighing system commonly found at truck stops across the United States. Unlike a basic platform scale that provides one overall reading, a typical CAT Scale has multiple platforms designed to measure individual axle groups.
For a conventional pickup truck towing a trailer, the three primary measurements are:
- Steer axle: The front axle of the towing truck.
- Drive axle: The rear axle of the towing truck.
- Trailer axle group: The axle or axle group supporting the trailer.
The readings allow you to see how the weight is distributed across your towing combination rather than relying on its total weight alone.
After weighing, you receive a scale ticket showing the individual axle-group readings and the combined weight.
You can locate participating facilities using the official CAT Scale locator.
What to Check Before Weighing Your Truck and Trailer
Preparation makes a significant difference to the accuracy and usefulness of your measurements.
The goal is to weigh your vehicle as it would actually be used on the road. An empty truck and unloaded trailer will not provide a realistic picture of your towing setup.
Before visiting the scale, prepare your combination as follows:
- Load the trailer with your normal camping equipment, tools, supplies, and cargo.
- Include the water and other onboard fluids you expect to carry during the trip.
- Put your usual passengers in the truck.
- Include the hitch, weight-distribution equipment, and other towing accessories.
- Carry approximately the amount of fuel you would normally have before departure.
- Check that the trailer is properly connected and secured.
- Locate the truck’s GVWR, front and rear GAWR, and GCWR ratings.
- Check the trailer’s GVWR and axle ratings.
Pay particular attention to the Tire and Loading Information sticker on the truck. It identifies the vehicle’s original occupant and cargo capacity information.
Advertised payload figures are not necessarily the payload available on your particular truck. Cab configuration, engine, drivetrain, factory options, and installed accessories can all affect the actual capacity.
It also helps to photograph the vehicle and trailer certification labels before visiting the scale so you can compare the readings with the correct ratings afterward.
How to Weigh a Truck and Trailer at a CAT Scale: Step-by-Step
Step 1: Find a CAT Scale Location
Start by using the CAT Scale location finder to find a participating truck stop.
Most facilities are designed primarily for commercial trucks, so the weighing area may be busy. Follow the posted instructions and avoid blocking truck traffic while preparing your vehicle.
If this is your first visit, ask the attendant how pickup trucks and recreational towing combinations should be positioned.
You should also check whether the facility offers the weighing and reweigh services you need.
Step 2: Position Your Truck and Trailer Correctly
Drive onto the scale slowly and follow the platform markings.
On a typical three-platform scale, the intended arrangement for a conventional pickup and single trailer axle group is:
| Scale platform | Vehicle section |
|---|---|
| Platform 1 | Truck front axle |
| Platform 2 | Truck rear axle |
| Platform 3 | Trailer axle group |
The front and rear truck axles should occupy their respective platforms, with the trailer axle group positioned on the third platform.
Keep the vehicle straight and make sure the axles are correctly positioned. An axle sitting across a platform boundary can produce readings that do not accurately represent its individual load.
Trailer configurations vary. If your trailer has multiple separated axle groups, an unusual wheelbase, or a long multi-axle arrangement, confirm the correct positioning procedure with the scale operator rather than assuming all axles can be measured in one pass.
Step 3: Obtain Your First Weighing Ticket
Once the vehicle is correctly positioned, follow the facility’s weighing procedure. You may be able to complete the transaction through the scale’s intercom or the supported CAT Scale weighing system.
Request a full combination weighing with the truck and trailer connected.
Your ticket should show the following readings:
- Steer axle weight
- Drive axle weight
- Trailer axle weight
Add the three readings to calculate the total combination weight.
For example:
| Measurement | Example weight |
|---|---|
| Front truck axle | 4,800 lbs |
| Rear truck axle | 5,600 lbs |
| Trailer axles | 8,400 lbs |
| Total combination weight | 18,800 lbs |
These are illustrative figures, not specifications for a particular vehicle.
Keep the ticket. You will need its readings when calculating the trailer’s loaded weight and the additional load carried by the truck.
Step 4: Weigh the Truck Without the Trailer
The first ticket tells you how much your complete combination weighs. To calculate the trailer’s actual loaded weight, you also need a truck-only measurement.
Find a safe, permitted parking area and unhitch the trailer according to the trailer and hitch manufacturers’ instructions. Do not unhitch on the scale platform unless the facility specifically permits and provides a safe procedure for doing so.
Leave the trailer loaded as it was during the first weighing.
Return to the scale with only the truck. Keep the passengers, cargo, fuel level, and accessories as consistent as possible.
Obtain another ticket showing the truck’s front and rear axle weights.
For example:
| Measurement | Truck alone |
|---|---|
| Front truck axle | 4,500 lbs |
| Rear truck axle | 3,800 lbs |
| Trailer axle | 0 lbs |
| Total truck weight | 8,300 lbs |
The third platform should be unoccupied.
The truck-only measurement provides the baseline needed to calculate the trailer’s loaded weight.
Step 5: Calculate the Trailer’s Loaded Weight
The calculation is straightforward:
Loaded trailer weight = Combined truck-and-trailer weight − Truck-only weight
Using the example figures:
18,800 lbs − 8,300 lbs = 10,500 lbs
The estimated loaded trailer weight is therefore 10,500 pounds.
This calculation includes the weight supported by the trailer axles and the portion transferred to the towing truck through the hitch.
That distinction is important. The trailer axle reading alone does not represent the trailer’s complete weight because some of its load is supported by the truck.
Step 6: Calculate the Weight Transferred to the Truck
You can use the two tickets to estimate how much additional weight the truck is carrying when connected to the trailer.
Subtract the truck-only axle readings from the corresponding truck axle readings on the combination ticket.
Using the example:
| Measurement | Combination setup | Truck alone | Difference |
|---|---|---|---|
| Front axle | 4,800 lbs | 4,500 lbs | +300 lbs |
| Rear axle | 5,600 lbs | 3,800 lbs | +1,800 lbs |
| Total truck axle increase | 10,400 lbs | 8,300 lbs | +2,100 lbs |
The truck’s total measured axle weight has increased by 2,100 pounds.
This represents the additional load carried by the truck in this example.
You can express that increase as a percentage of the trailer’s total loaded weight:
2,100 ÷ 10,500 × 100 = 20%
The truck is carrying an additional load equivalent to 20% of the trailer’s total weight.
However, there is an important distinction between this calculation and actual tongue or pin weight.
With a conventional hitch that does not redistribute weight, the increase in the truck’s total axle weight can be used to estimate the vertical hitch load. With a weight-distribution hitch, some of that load is transferred back to the trailer axles and redistributed between the truck’s front and rear axles.
Consequently, the difference between the two truck tickets represents the additional weight retained by the truck, not necessarily the trailer’s original tongue or pin weight.
For an accurate tongue-weight measurement with a weight-distribution system, follow the manufacturer’s weighing procedure and account for the hitch configuration.
You can also learn more about how trailer tongue weight is measured and why it matters.
Step 7: Check Your Axle Loads and Vehicle Ratings
Once you have both tickets, compare the measurements with the manufacturer’s ratings.
Pay attention to:
- Truck GVWR
- Front GAWR
- Rear GAWR
- GCWR
- Trailer GVWR
- Trailer axle ratings
- Tire load ratings
For a more complete assessment, you should also consider the hitch receiver, ball mount, fifth-wheel hitch, and other towing equipment ratings.
A truck can be below its advertised maximum towing capacity while exceeding its payload or rear axle rating.
If you use a weight-distribution hitch, obtain the additional measurements needed to check how the system distributes the load across all axle groups.
How to Read Your CAT Scale Ticket
The numbers on a CAT Scale ticket become useful when you understand which vehicle rating each reading needs to be compared against.
Here are the main terms:
| Rating | Meaning | What to compare |
|---|---|---|
| GVWR | Gross Vehicle Weight Rating | Actual loaded truck weight |
| GAWR | Gross Axle Weight Rating | Individual axle weights |
| GCWR | Gross Combined Weight Rating | Total truck-and-trailer weight |
| Trailer GVWR | Maximum rated trailer weight | Actual loaded trailer weight |
| Tire load rating | Maximum permitted tire load under specified conditions | Actual load carried by each tire or tire group |
Consider a truck with a GVWR of 10,000 pounds.
Suppose its measured weight when loaded and connected to a trailer is 10,100 pounds.
The truck is 100 pounds above its GVWR, even if the combined truck-and-trailer weight remains below its GCWR.
There is another important possibility: the truck’s total weight might be below its GVWR while its rear axle exceeds its individual GAWR.
This is why a complete assessment requires more than looking at the total combination weight.
For a closer explanation of these ratings, see our guides to GVWR on a truck and GCWR and how it differs from GVWR and towing capacity.
What If Your Truck or Trailer Is Overweight?
If the scale readings show that your truck, trailer, axle, or tire load exceeds its applicable rating, identify the source before continuing with your towing setup.
Possible contributors include:
- Excessive cargo in the truck bed.
- Too much equipment or water inside the trailer.
- Excessive tongue or fifth-wheel pin load.
- Incorrect trailer cargo distribution.
- A weight-distribution hitch that is not adjusted correctly.
- Tires or towing components with insufficient load capacity.
Depending on the measurements, possible adjustments include:
- Remove unnecessary cargo from the truck or trailer.
- Redistribute trailer cargo according to the manufacturer’s loading instructions.
- Review the hitch installation and weight-distribution setup.
- Check the tire and wheel load ratings.
- Consider a vehicle or trailer with higher appropriate weight ratings if the combination cannot be brought within its limits.
Do not assume that moving cargo from the truck to the trailer automatically fixes an overweight condition. The final axle loads, vehicle ratings, trailer ratings, and tire capacities must all be checked.
If the readings remain above a manufacturer’s rating, have the setup evaluated before towing.
Common Mistakes When Weighing a Truck and Trailer
Even a properly functioning scale can produce misleading conclusions if the vehicle is not prepared or positioned correctly.
These are some common mistakes to avoid.
Weighing an empty trailer: An unloaded trailer does not represent its normal travel weight. Include the cargo, water, equipment, and supplies you typically carry.
Ignoring passengers: Passengers contribute to the truck’s loaded weight and payload. Removing them for the truck-only measurement can make the results inaccurate for your actual travel configuration.
Relying on advertised payload: Different trims, engines, cab configurations, and factory options affect available payload. Use the specific truck’s certification information and payload sticker.
Confusing trailer axle weight with total trailer weight: The trailer axles do not necessarily support the entire trailer load. Some weight is transferred to the towing vehicle through the hitch.
Ignoring individual axle ratings: A combination that is below its GCWR can still have an overloaded front or rear axle.
Changing the loading conditions between weighings: Different fuel levels, passengers, cargo, and accessories can affect the comparison between the two tickets.
Ignoring weight-distribution equipment: A weight-distribution hitch changes how the load is shared between the truck and trailer axles. Its configuration must be considered when interpreting the readings.
How Much Does It Cost to Weigh a Truck and Trailer at a CAT Scale?
CAT Scale charges depend on the service and applicable pricing at the time of weighing.
A standard weighing provides the initial combination ticket. If you want to calculate the trailer’s loaded weight and compare the truck’s axle loads with the trailer connected and disconnected, you will need an additional truck-only weighing.
Some facilities also offer reweigh services under their applicable pricing arrangements.
Before visiting, check the current service information through the official CAT Scale website. Do not assume that the price of an initial weighing automatically covers every additional ticket you need.
For accurate budgeting, confirm the charges with the facility.
Frequently Asked Questions
Can I weigh my pickup truck and travel trailer at a CAT Scale?
Yes. CAT Scales can weigh pickup trucks towing travel trailers, fifth-wheels, and other compatible trailer combinations. The axles must be positioned correctly on the available platforms, following the facility’s instructions.
Do I need to unhitch my trailer to weigh it?
No. You can obtain the initial combined weight with the trailer connected.
However, a separate truck-only weighing is useful if you want to calculate the trailer’s total loaded weight and determine how much additional weight the truck carries when connected.
How do I calculate trailer weight from CAT Scale tickets?
Subtract the truck-only weight from the combined truck-and-trailer weight.
For example:
18,800 lbs − 8,300 lbs = 10,500 lbs.
The estimated loaded trailer weight is 10,500 pounds.
How do I calculate fifth-wheel pin weight?
Compare the truck’s front and rear axle readings with the fifth-wheel connected against the corresponding readings with the truck alone.
The increase in the combined truck axle weight shows the additional load retained by the truck.
If a fifth-wheel hitch or other equipment redistributes the load, this difference should not automatically be treated as the original pin weight. Follow the appropriate weighing procedure to account for load transfer.
Can a truck be below its towing capacity but still be overweight?
Yes. Towing capacity, payload, GVWR, GAWR, and GCWR represent different limits.
A truck might be capable of towing a trailer within its advertised towing rating while exceeding its payload or rear axle rating once passengers, cargo, and hitch weight are included.
Is one CAT Scale ticket enough?
One combination ticket provides the individual axle-group readings and total combined weight.
However, a second truck-only ticket is useful for calculating the trailer’s total loaded weight and the additional weight carried by the truck.
Can I weigh my truck and trailer without unloading anything?
Yes. In fact, weighing the combination with your normal travel cargo, passengers, and equipment gives you a more realistic picture of its actual operating weight.
You should keep the trailer loaded between the combination and truck-only measurements. Only the trailer should be disconnected for the second weighing.
Does a CAT Scale tell me whether my truck is safe for towing?
The scale provides measured axle-group and combination weights. It does not independently certify that your complete towing setup is safe.
You must compare the readings with the vehicle, trailer, tire, and hitch manufacturers’ ratings. Also consider the condition and adjustment of the towing equipment.
Conclusion
Weighing your truck and trailer at a CAT Scale provides information that manufacturer towing specifications cannot give you: the actual weight of your loaded combination.
The first ticket shows the weight carried by the truck and trailer axle groups together. A second truck-only weighing allows you to calculate the trailer’s total loaded weight and determine how much additional load the truck carries when connected.
The most important part is interpreting the readings correctly. Check the GVWR, GAWR, GCWR, trailer ratings, tire capacities, and hitch specifications rather than relying on a single total-weight figure.
If you tow regularly, consider weighing your combination after changing trailers, installing substantial accessories, or significantly changing your cargo.
A properly interpreted scale ticket gives you a much clearer understanding of your towing setup and helps you identify loading problems before starting your next trip.